News About Us Distributor Log-In Contact Us
Products Certifications Downloads Resources Configurator
 
Find a Distributor
Home   ›   Products   ›   Cylinders   ›   Series MH
 

Series MH – Metric Hydraulic Tie Rod Cylinders


MILWAUKEE Series "MH" hydraulic tie rod cylinders are built to perform on the toughest applications. Incorporating a variety of MILWAUKEE "Exclusive" advanced features, proven through the years, these cylinders will provide a long, maintenance-free service life. Advanced engineering combined with quality materials and expert workmanship contribute to the making of a rugged, top quality hydraulic cylinder. Milwaukee Cylinder MH Metric Cylinders meet ISO Standard 6020/2 160 bar series, including working pressures up to 210 bar.

Series MH Features & Benefits

 Series MH Catalog PDF (1.21 MB)

Tie-Rod Mount
Solid End Cap and Side Lug Mount
Pin Mount
Trunnion Mount
Double Rod End

TIE-ROD MOUNT (Back to Top)
The flange and tie-rod mounts are basically the same, except that the cylinder tie rods are extended and used to mount the cylinder. To prevent misalignment, sagging or possible binding of the cylinder, the free end should be supported. The best use of tie-rods when extending on the blind end is in a thrust load application. When using tie-rods extended on the rod end, the best application is a tension load. Tie rod mounts are suited for many applications, but it should be noted that they are not as rigid as the flange type of mounting.


Both Ends
Model MH10
ISO MX1
25mm to 200mm Bore


Rod End
Model MH12
ISO MX3
25mm to 200mm Bore


Blind End
Model MH13
ISO MX2
25mm to 200mm Bore

SOLID END CAP and SIDE LUG MOUNT (Back to Top)
The side lug mounted cylinder provides a fairly rigid mount. These types of cylinders can tolerate a slight amount of misalignment when the cylinder is at full stroke, but as the piston moves toward the blind end, the tolerance for misalignment decreases. It is important to note that if the cylinder is used properly (without misalignment), the mounting bolts are either in simple shear or tension without any compound stresses.


Solid Rod End Cap
Model MH35
ISO ME5
25mm to 200mm Bore


Solid Blind End Cap
Model MH36
ISO ME6
25mm to 200mm Bore


 
Side Lug
Model MH42
ISO MS2
25mm to 200mm Bore

PIN MOUNT (Back to Top)
All pin mount cylinders need a provision on both ends for pivoting. These types of cylinders are designed to carry shear loads and the pins should be carred by bearings that are rigidly held and closely fit for the entire length of the pin.


Clevis
Model MH61
ISO MP1
25mm to 200mm Bore


Clevis
Model MH64
ISO MP3
25mm to 200mm Bore


Fixed Eye Spherical Bearing
Model MH62
ISO MP5
25mm to 200mm Bore

TRUNNION MOUNT (Back to Top)
All trunnion mount cylinders need a provision on both ends for pivoting. These types of cylinders are designed to carry shear loads and the trunnion pivot pins should be carred by bearings that are rigidly held and closely fit for the entire length of the pin.


Rod End Trunnion
Model MH71
ISO MT1
25mm to 200mm Bore


Blind End Trunnion
Model MH72
ISO MT2
25mm to 200mm Bore


Center Trunnion
Model MH74
ISO MT4
25mm to 200mm Bore

DOUBLE ROD END (Back to Top)
Double rod end styles are available in every mounting style except clevis. On double rod end cylinders where the rod ends are not the same, be sure to specify clearly which rod end is to go at which end of the cylinder in relation to your mounting requirements.


Double Rod End
ISO MDX
25mm to 200mm Bore

 

Specials are Our Standard
Sign up for eNews Sign up for eNews
Milwaukee Cylinder
5877 S. Pennsylvania Ave. Cudahy, WI 53110-2456 USA
Phone: 414-769-9700 Fax: 414-769-0157