Specials are Our Standard          

Home •   Request Quote •   About Us •   Products •   MilCad •   Distributors •   Literature •   Contact
ISO 9001 Registered

Pneumatic Cylinders – Steel
 
Pneumatic Cylinders – Aluminum
 
Hydraulic Cylinders – Low Pressure
 
Hydraulic Cylinders – Heavy Duty

Features & Benefits
Series H Catalog PDF (2.01 MB)

Tie Rod Mount

(1.5" to 12")

MX MX1 MX2      MX3

Flange Mount

(1.5" to 12")

MF1 MF2 MF5 MF6

Side and Lug Mount

(1.5" to 12")

MS2 MS3 MS4 MS7

Pin and Trunnion

(1.5" to 12")

MP1 MT1 MT2 MT4

Solid End Cap Mount

(1.5" to 12")

ME5 ME6

Other

(1.5" to 12")

Key Mount Double Rod End

Piston Rod End Styles
Ports Table
 
Hydraulic Cylinders – Metric (ISO) 
 
Accessories 
 
Power Units 
 
Industrial Manipulators 
 
Position Sensing
& Motion Control
 
 
Proximity Switches 
 
Design Engineer's Guide 
 
Request Quote 


PARTNERS LOG-IN

 
MilCad Cylinder Configurator
 

Series H – Heavy Duty Hydraulic Cylinders

MILWAUKEE Series "H" hydraulic cylinders are built to perform on the toughest applications. Incorporating a variety of MILWAUKEE "Exclusive" advanced features, proven through the years, these cylinders will provide a long, maintenance-free service life. Advanced engineering combined with quality materials and expert workmanship contribute to the making of a rugged, top quality hydraulic cylinder.

Series H Features & Benefits

 Series H Catalog PDF (2.01 MB)

Tie-Rod Mount
Flange Mount
Side And Lug Mounts
Pin and Trunnion Mounts
Solid End Cap Mounts
Key Mount
Double Rod End

TIE-ROD MOUNTS (Back to Top)
The flange and tie-rod mounts are basically the same, except that the cylinder tie rods are extended and used to mount the cylinder. To prevent misalignment, sagging or possible binding of the cylinder, the free end should be supported. The best use of tie-rods when extending on the blind end is in a thrust load application. When using tie-rods extended on the rod end, the best application is a tension load. Tie rod mounts are suited for many applications, but it should be noted that they are not as rigid as the flange type of mounting.


Both Ends
Model H10
NFPA MX1
1.5" to 12" Bore


No Extension
Model H11
NFPA MX
1.5" to 12" Bore


Rod End
Model H12
NFPA MX3
1.5" to 12" Bore


Blind End
Model H13
NFPA MX2
1.5" to 12" Bore

FLANGE MOUNTS (Back to Top)
The flange mount is one of the strongest, most rigid methods of mounting. With this type of mount there is little allowance for misalignment, though when long strokes are required, the free end opposite the mounting should be supported to prevent sagging and possible binding of the cylinder. The best use of a blind end flange is in a thrust load application (rod in compression). Rod end flange mounts are best used in tension applications. If an application exceeds the rectangular flange rating, requiring an extra heavy flange, a solid flange style end cap mount is available at no extra cost for most bore sizes. When a less rigid mount can be used and the cylinder can be attached to a panel or bulkhead, an extended tire rod mounting could be considered.


Rod Square
Model H21
NFPA MF5
1.5" to 12" Bore


Blind Square
Model H22
NFPA MF6
1.5" to 12" Bore


Rod Rectangular
Model H31
NFPA MF1
1.5" to 12" Bore


Blind Rectangular
Model H32
NFPA MF2
1.5" to 12" Bore

SIDE AND LUG MOUNTS (Back to Top)
The side or lug mounted cylinder provides a failrly rigid mount. These types of cylinders can tolerate a slight amount of misalignment when the cylinder is at full stroke, but as the picton moves toward the blind end, the tolerance for misalignment decreases. It is important to note that if the cylinder is used properly (without misalignment), the mounting bolts are either in simple shear or tension without any compound stresses.


Tapped Holes
in Caps Flush
Model H41
NFPA MS4
1.5" to 12" Bore


 
Side Lug
Model H42
NFPA MS2
1.5" to 12" Bore


 
Foot
Model H43
NFPA MS7
1.5" to 12" Bore


 
Centerline Lug
Model H51
NFPA MS3
1.5" to 12" Bore

PIN AND TRUNNION MOUNTS (Back to Top)
All pin and trunnion cylinders need a provision on both ends for pivoting. These types of cylinders are designed to carry shear loads and the trunnion pivot pins should be carred by bearings that are rigidly held and closely fit for the entire length of the pin.


Clevis
Model H61
NFPA MP1
1.5" to 12" Bore


Rod End Trunnion
Model H71
NFPA MT1
1.5" to 12" Bore


Blind End Trunnion
Model H72
NFPA MT2
1.5" to 12" Bore


Center Trunnion
Model H73
NFPA MT4
1.5" to 12" Bore

SOLID END CAP MOUNTS (Back to Top)
Milwaukee Cylinder’s solid end cap mounts are one of the strongest, most rigid methods of mounting. Solid rod end cap mounts are best in a tension application; solid blind end cap mounts are best in a thrust load application.


Solid Rod End Cap
Model H35
NFPA ME5
1.5" to 12" Bore


Solid Blind End Cap
Model H36
NFPA ME6
1.5" to 12" Bore

Key Mount (Back to Top)
The Milwaukee Key Mount retainer plate is a mounting option designed to add rugged stability to foot and side mount cylinders. The retainer plate is extended below the mouting surface of the cylinder. This extension may be fitted ino a milled keyway in your mouting pad, eliminating the need for welded keys or locator pins.


Model
Key Mount
1.5" to 12" Bore

Double Rod End (Back to Top)
Double rod end styles are available in every mounting style except clevis. On double rod end cylinders where the rod ends are not the same, be sure to specify clearly which rod end is to go at which end of the cylinder in relation to your mounting requirements.


Double Rod End
NFPA MDX
1.5" to 12" Bore

Milwaukee Cylinder

Milwaukee Cylinder
5877 S. Pennsylvania Ave. • Cudahy, WI 53110-2456 USA
www.milwaukeecylinder.com • sales@milwaukeecylinder.com
Phone: 414-769-9700• Fax: 414-769-0157