 |
|
|
|
Tie Rod Mount
|
(25 to 200mm)
|
|
|
|
|
 |
|
Side Lug Mount
|
(25 to 200mm)
|
|
|
|
|
Pin Mount
|
(25 to 200mm)
|
|
|
|
|
|
|
Trunnion Mount
|
(25 to 200mm)
|
|
|
|
|
|
|
Solid Flange Mount
|
(25 to 200mm)
|
|
|
|
|
|
Double Rod End
|
(25 to 200mm)
|
|
|
|
|
|
|
|
|
|
PARTNERS LOG-IN
|
|
|
|
TIE-ROD MOUNTS (Back to Top)
The flange and tie-rod mounts are basically the same, except that the cylinder tie rods are extended and used to mount the cylinder. To prevent misalignment, sagging or possible binding of the cylinder, the free end should be supported. The best use of tie-rods when extending on the blind end is in a thrust load application. When using tie-rods extended on the rod end, the best application is a tension load. Tie rod mounts are suited for many applications, but it should be noted that they are not as rigid as the flange type of mounting.
|
Both Ends
Model H10M
ISO MX1
25mm to 200mm Bore
|
Rod End
Model H12M
ISO MX3
25mm to 200mm Bore
|
Blind End
Model H13M
ISO MX2
25mm to 200mm Bore
|
SIDE LUG MOUNT (Back to Top)
The side lug mounted cylinder provides a failrly rigid mount. These types of cylinders can tolerate a slight amount of misalignment when the cylinder is at full stroke, but as the picton moves toward the blind end, the tolerance for misalignment decreases. It is important to note that if the cylinder is used properly (without misalignment), the mounting bolts are either in simple shear or tension without any compound stresses.
|
Side Lug
Model H42M
ISO MS2
25mm to 200mm Bore
|
PIN MOUNTS (Back to Top)
All pin mount cylinders need a provision on both ends for pivoting. These types of cylinders are designed to carry shear loads and the pins should be carred by bearings that are rigidly held and closely fit for the entire length of the pin.
|
Clevis
Model H61M
ISO MP1
25mm to 200mm Bore
|
Plain Eye
Model H64M
ISO MP3
25mm to 200mm Bore
|
Fixed Eye Spherical Bearing
Model H62M
ISO MP5
25mm to 200mm Bore
|
TRUNNION MOUNTS (Back to Top)
All trunnion mount cylinders need a provision on both ends for pivoting. These types of cylinders are designed to carry shear loads and the trunnion pivot pins should be carred by bearings that are rigidly held and closely fit for the entire length of the pin.
|
Rod End Trunnion
Model H71M
ISO MT1
25mm to 200mm Bore
|
Blind End Trunnion
Model H72M
ISO MT2
25mm to 200mm Bore
|
Center Trunnion
Model H74M
ISO MT4
25mm to 200mm Bore
|
DOUBLE ROD END (Back to Top)
Double rod end styles are available in every mounting style except clevis. On double rod end cylinders where the rod ends are not the same, be sure to specify clearly which rod end is to go at which end of the cylinder in relation to your mounting requirements.
|
Double Rod End
ISO MDX
25mm to 200mm Bore
|
|
MILWAUKEE Series "MH" hydraulic cylinders are built to perform on the toughest applications. Incorporating a variety of MILWAUKEE "Exclusive" advanced features, proven through the years, these cylinders will provide a long, maintenance-free service life. Advanced engineering combined with quality materials and expert workmanship contribute to the making of a rugged, top quality hydraulic cylinder. Milwaukee Cylinder MH Metric Cylinders meet ISO Standard 6020/2 160 bar series, including working pressures up to 210 bar.
Series MH Catalog PDF (1300 KB)
